SAE J1885-2005 用可控制不发光 的水冷氙弧灯进行汽车内饰的快速暴露

®

REV.

MAR2005

SURFACE

J1885

VEHICLE

Issued 1987-08

Revised 2005-03

STANDARD

Superseding J1885 MAR1992

Accelerated Exposure of Automotive Interior Trim Components Using a

Controlled Irradiance Water Cooled Xenon-Arc Apparatus

This document is equivalent to ISO/DIS 105-B06 option 5.

1. Scope

This test method specifies the operating procedures for a controlled irradiance, water cooled xenon-arc

apparatus used for the accelerated exposure of various automotive interior trim components.

Test durations, as well as any exceptions to the sample preparation and performance evaluation

procedures contained in this document, are covered in material specifications of the different automotive

manufacturers.

This standard is limited to the models of xenon arc test apparatus specified in the Section on Equipment.

All other models of xenon arc test apparatus must use SAE J2412 to perform the test conditions specified

in SAE J1885. SAE J2412 is the performance standard based on the test parameters of SAE J1885.

Use of xenon arc test apparatus to perform SAE J2412 must be agreed upon by contractual parties.

1.1 Rationale

The Scope has been revised to harmonize with the corresponding performance-based document.

References to supplier names and addresses have been removed throughout the document to comply

with SAE procedures.

2.

2.1

References

Applicable Publications

The following publications form a part of this specification to the extent specified herein. The latest issue

of SAE publications shall apply.

SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is

entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”

SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.

Copyright © 2005 SAE International

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,

recording, or otherwise, without the prior written permission of SAE.

TO PLACE A DOCUMENT ORDER:

Copyright SAE International

SAE WEB ADDRESS:

Provided by IHS under license with SAE

No reproduction or networking permitted without license from IHS

Tel: 877-606-7323 (inside USA and Canada)

Tel: 724-776-4970 (outside USA)

--`,,,```-`-`,,`,,`,`,,`---

Fax: 724-776-0790

Email: custsvc@

Not for Resale

SAE J1885 Revised MAR2005

2.1.1 SAE

P

UBLICATIONS

2.1.2 ASTM

P

UBLICATION

Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.

ASTM G 26—Standard Practice for Operating Light-Exposure Apparatus (Xenon-Arc Type) With and

Without Water for Exposure of Nonmetallic Materials

2.1.3 ISO

P

UBLICATION

Available from ANSI, 25 West 43rd Street, New York, NY 10036-8002.

ISO 105 B06—Textiles—Tests for colour fastness—Colour fastness to artificial light at high temperatures:

Xenon arc fading lamp test

2.1.4 O

THER

P

UBLICATIONS

AATCC Evaluation Procedure 1 (1987)—Available from American Association of Textile Chemists and

Colorists, P.O. Box 12215, Research Triangle Park, NC 27709, Tel: 919/549-8141, .

Polystyrene Plastic Lightfastness Standard Lot#1—Available from Test Fabrics, nc., 415 Delaware

Avenue, West Pittston, PA 18643.

3.

3.1

Definitions

Black Panel Thermometer, n

A temperature measuring device, the sensing unit of which is a stainless steel panel coated with black

material designed to absorb most of the radiant energy encountered in fade/weathering testing.

NOTE—This device provides an estimation of the maximum temperature a specimen may attain during

exposure to natural or artificial light.

3.2 Blue Wool Lightfastness Standard, n

One of a group of dyed fabrics used to determine the amount of light, or combined light, heat, and

moisture to which a specimen is exposed during fade/weathering testing.

Copyright SAE International

Provided by IHS under license with SAE

No reproduction or networking permitted without license from IHS

- 2 -

Not for Resale

-

-

`

,

,

,

`

`

`

-

`

-

`

,

,

`

,

,

`

,

`

,

,

`

-

-

-

Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.

SAE J1545—Instrumental Color Difference Measurement for Exterior Finishes, Textiles, and Colored

Trim

SAE J1885—Accelerated Exposure of Automotive Interior Trim Components Using a Controlled

Irradiance Water Cooled Xenon-Arc Apparatus

SAE J2412—Accelerated Exposure of Automotive Interior Trim Components Using a Controlled

Irradiance Xenon-Arc Apparatus